Questions tagged [connector]
Mechanical part providing electrical contacts for a cable or electronic circuit board.
2,263
questions
4
votes
1
answer
317
views
How to connect to "upstands" on the PCB without soldering?
I've got two items of the same model number, but one of them has a Phoenix type terminal on the PCB for the connection. See photo below.
The other one has "upstands" poking out of the PCB.
...
2
votes
1
answer
165
views
Matching power supply to a four pin connector
There is a Power supply called HRPG-150-48. I need to deliver its voltage into a special 4 pin kind of connector.
For me a connector needs only two pins GND and voltage.
Given the data sheet of the ...
-5
votes
0
answers
52
views
Draw the following circuit [closed]
Draw the following circuit according to the condition below : switch one 1must switch lamp 1only and switch 2should only switch Lamp 2,,,,, when either switch or lamp is on , the other switch or ...
1
vote
1
answer
29
views
5 Pin Equivalent of MT-30 Connector [closed]
Normally I connect 2 different harnesses with 3 wires together with MT-30 connector, but I need to add 2 more wires and increase the number of wires to 5. I am looking for a 5 pin equivalent of the MT-...
1
vote
1
answer
49
views
Connection for Hoover washer dryer drain pump
I am replacing the drain pump on my Hoover washer dryer and found that the electrical connection is not compatible with the new pump. In the old pump (top one in picture) the wires plug in with 1 ...
1
vote
0
answers
48
views
Identification of 3 pin connector for the power supply of the TI silent Model 703/707 Data Terminal [closed]
I want to restore a TI Silent 700 model 703/707 that lacks the power supply.
The power supply provides 20 VAC 35 VA with 3 pins
...
1
vote
1
answer
57
views
What is the type of this connector?
I have to find the female connector for this male one. I do not want to use all the pins so I would be happy with a configurable mother connector. Is that existing? Many thanks in advance!
2
votes
1
answer
129
views
Unexpected Loss In Signal Integrity
For a project I'm working on, I wanted to clone this e-paper driver board and eventually integrate it into my project's board.
Here's a part of the schematic:
However, with my custom prototype clone ...
2
votes
1
answer
297
views
KiCAD symbols for JST connectors
I'm trying to add JST connectors library to my KiCAD installation. I'm using KiCAD 8.
I see that Connector_JST is in the KiCAD footprints and the KiCAD 3D shapes but not in the KiCAD symbols.
How come ...
1
vote
1
answer
67
views
What type of connector is this, and how can one reliably detach and re-attach?
These connectors are from a vintage component audio system (Kenwood X-MB3, to be specific).
Can someone help on how to reliably detach these from the base, and re-attach without any damage? The ...
3
votes
1
answer
104
views
Help identifying hollow spring / inverted header sockets
I'm trying to identify the following hollow sockets which are used to interface with a 0.1" pitched header:
(source: US Digital PC5 Broadcom/Avago Compatible Incremental Encoder Cable Driver. ...
0
votes
1
answer
47
views
Suggest appropriate substitute for cable glands
I have a 3.3 mm cable coming from a sensor (3.3 V) and going to an instrument.
I would not like any joints in the path in the form of connectors which could make problems for the sensor if the ...
2
votes
2
answers
67
views
Unknown wire to board connector
i have a wire to board connector for a rice cooker & need to replicate it.
I have no idea who makes it...it seems to resemble a JST XA but not certain.
Pitch is 2.54 2 pin.
0
votes
1
answer
42
views
How to solder the central pin of the TGA 2214-CP microwave amplifier
Here is datasheet of the TGA 2214-CP amplifier: TGA 2214-CP
The pins can be seen on page 11. It turns out that pin 7 and 9 are very close to the central pin 1, as well as pin 8 and 10 to pin 2 (about ...
1
vote
0
answers
62
views
What's this damaged 3-pin rectangular power connctor on a FLIR thermal camera?
I'm hoping this is a standard-ish connector but I have my doubts.
It's the 12V power line that plugs into the battery or charging dock of a FLIR T335/T365.
Measuring the undamaged part the overall ...