Lenovo released a new firmware 1.30 which is available on LVFS and also available via Lenovo Support Site

After flashing you will need to enable it under Setup → Config → Power then select Linux.

But don't forget to reverse this scripts effects and manual changes in your bootloader config before rebooting.

# remove the patch
rm /boot/acpi_override

# on ubuntu / debian based system
rm /etc/initramfs-tools/hooks/acpi_override.sh

Many modern distros automatically install the updates from LVFS but you can check manually via:

If you have a device with firmware supported by fwupd, this is how you will check for updates and apply them using fwupd's command line tools.

# fwupdmgr get-devices

This will display all devices detected by fwupd.

# fwupdmgr refresh

This will download the latest metadata from LVFS.

# fwupdmgr get-updates

If updates are available for any devices on the system, they'll be displayed.

# fwupdmgr update

This will download and apply all updates for your system.

    Updates that can be applied live will be done immediately.
    Updates that run at bootup will be staged for the next reboot.

You can manually check your BIOS version like this:

sudo dmidecode | grep "BIOS Revision:"

To update your BIOS via USB drive use geteltorito.

curl -O https://download.lenovo.com/pccbbs/mobiles/n23ur11w.iso
geteltorito -o x1c2018-130.img n23ur11w.iso
sudo dd if=x1c2018-130.img of=/dev/sdX bs=512K

Unfortunately the ThinkPad X1 Yoga (3rd Gen) aka (X1Y3 and X1 Yoga 2018) does not support suspend on Linux. There's an ongoing discussion in the Lenovo Support Forums. With some help from the Arch Linux Community, I was able to create an ACPI override for the DSDT. This enables full support of S3 suspend on Linux.

Debian/Ubuntu based distro with initramfs-tools based initramfs generation for fully automated setup apart from the BIOS related things.

For other distros there are some further steps needed. (PRs welcome) Reboot from USB and follow instructions.

• Ensure that Boot Mode is set to Quick and not Diagnostic
• Set Thunderbolt BIOS Assist Mode to Enabled (via Config → Thunderbolt 3).
• Disable Secure Boot.

If you see all three lines in dmesg | grep -A3 'DSDT ACPI'

[    0.000000] ACPI: DSDT ACPI table found in initrd [kernel/firmware/acpi/dsdt.aml][0x2338b]
[    0.000000] Lockdown: ACPI table override is restricted; see man kernel_lockdown.7
[    0.000000] ACPI: kernel is locked down, ignoring table override

rather than just the first line, disable Secure Boot

Make sure that you have iasl (via acpica) and cpio (via cpio) installed.

Installed automatically on distros with apt such as Debian/Ubuntu

curl -O https://raw.githubusercontent.com/fiji-flo/x1carbon2018s3/master/generate_and_apply_patch.sh
chmod +x generate_and_apply_patch.sh
./generate_and_apply_patch.sh

Edit your boot loader configuration and add /acpi_override to the initrd line. To ensure S3 is used as sleep default add mem_sleep_default=deep to you kernel parameters.

If you're using systemd-boot your /boot/loader/entries/arch.conf might look like this:

title		Arch Linux ACPI
linux		/vmlinuz-linux
initrd		/intel-ucode.img
initrd		/acpi_override
initrd		/initramfs-linux.img
options		root=/dev/nvme0n1p2 rw i915.enable_guc=3 mem_sleep_default=deep

If you're using grub edit /etc/default/grub and add the following:

GRUB_EARLY_INITRD_LINUX_CUSTOM=acpi_override
GRUB_CMDLINE_LINUX_DEFAULT="quiet mem_sleep_default=deep"

Then run sudo update-grub. To verify the setting has been applied correctly run sudo cat /boot/grub/grub.cfg | grep initrd and you should see:

initrd  /boot/intel-ucode.img /boot/acpi_override /boot/initramfs-4.19-x86_64.img

If you made it work with other boot loaders please help out (PRs are most welcome).

• /acpi_override must be specified before /initramfs….
• When using a single partiion try using /boot/acpi_override instead of acpi_override. Use the same prefix (if any) used by the existing /prefix/initramfs-linux.img parameter.

After rebooting check the output of:

dmesg | grep -i "acpi: (supports"

should look like this:

[    0.230796] ACPI: (supports S0 S3 S4 S5)

Esonn did an initial blog post about my patch with some more detailed explanation.