Questions tagged [hot-plug]
The act of connecting a communication interface between two devices while one or both are powered up. The design of interfaces to tolerate this.
22
questions
1
vote
1
answer
38
views
Hot pluggable CAN collections of devices
I'm trying to create a network of hot pluggable collections of iot devices into a bus (Containing Device 'A') that will always be present. There could be up to 50 collections with each collection ...
0
votes
0
answers
119
views
PCIe hotplug hardware schematics reference design
I was going through this link, this was very wonderful
Does PCIe hotplug actually work in practice?
Following the above link, I had a question below:
I am looking for a "PCIe hotplug hardware ...
0
votes
0
answers
247
views
Display Port 1.4 Hot Plug Detect (HPD) Behaviour on AMD 7040 Motherboard
For some reason I can't get my DP port working on the AMD 7040 motherboard that I have designed, where on the same board, I have also Mini-DP that has an identical electrical circuit (in schematic) ...
-1
votes
1
answer
164
views
Hot-plugging current - TVS and ethernet
My question is based on this question over here
In one of the comments, it is mentioned,
"TVS on the media side would seem to invite short-circuit currents on hot-plugging. Putting it behind the ...
2
votes
0
answers
425
views
Serial circuit protection design
I've been researching RS485 hotplug protection for a while and come up with the following solution. The reason is that I burned two custom Arduinos, after further investigation it turned out the GND ...
1
vote
1
answer
45
views
Replace a DS4560S hotplug protection IC with a custom circuit
I intended to use a DS4560S for hotplug protection for my custom Arduinos. Unfortunately it turned out my fab house doesn't have them available even at their supplier and it would be a great hassle. ...
1
vote
0
answers
199
views
Hotplug protection for serial devices
I'm building a cockpit for home entertainment and have decided on RS485 for communication and, unfortunately RJ45 to carry the power and data to the panels. I have already made a lot of hardware with ...
1
vote
2
answers
103
views
Hot-pluggable bus design review
I am currently designing a hot-pluggable bus system where a module is connected to its respective slot via a first mate/last break spring-loaded connector. I am using PJON, in specific PJDL on the ...
3
votes
1
answer
135
views
USB hotplugging causes latchup in LDO
I am working on a device that is powered from a USB host and has a downstream-facing USB type A receptacle. VBUS on the downstream port is connected directly to VBUS on the upstream port, and 3.3V ...
2
votes
1
answer
6k
views
What is the correct behavior of the HDMI HPD signal?
Can anybody explain the correct behavior the HDMI HPD (Hot Plug Detect) signal?
For example, I've disassembled an HDMI coupler and connected a few wires to the +5V/HPD/GND (shell) and here is what I'm ...
0
votes
0
answers
149
views
Hotplugging issue in MicroSD Connector
I am facing a hotplugging issue in my SD Connector setup. When I plug and check, it reads, however, not when I remove and insert. What might be the reason behind this? Attached are the schematics for ...
1
vote
1
answer
985
views
Leaving DVI hot plug detect pin unconnected
I am making a custom cable from a VPX backplane to a DVI-I connector, and need to know if the DVI cable will work OK with a standard monitor if I do not wire up the hot plug detect pin. I will never ...
1
vote
2
answers
503
views
What makes signal lines hot swappable?
In MAX14780E datasheet, it's explicitly featured as "hot swappable", however in AM26C31 datasheet this isn't mentioned. Moreover, I suspect that I burnt one of the AM26C31 ICs while hot ...
2
votes
1
answer
313
views
Why is my Pi Pico resetting from HDMI hotplug (transients question)
Why exactly is my Raspberry Pi Pico (MCU) resetting during HDMI hotplugs with my simple HDMI signal sniffing circuit? Although the solution to this is obvious, I'm curious as to exactly what's ...
2
votes
1
answer
596
views
What is the best way of implementing ethernet over a custom pogo pin connector?
I'm designing a custom hot swap connector with pogo pin contacts, similar to that of an electronic camera lens. I am wondering if there are any special considerations I should be taking if I want to ...